Network Isolator MED MI 1005

Network isolator for the isolation of medical equipment Safety: IEC 60601-1:2012 (Edition 3.1... more
Product information "Network Isolator MED MI 1005"

Network isolator for the isolation of medical equipment

Safety: IEC 60601-1:2012 (Edition 3.1 Medical electrical equipment)
EMV: EN 60601-1-2:2015  (IEC 60601-1-2:2014) (Medical electrical equipment)

Our Network Isolator MED MI 1005 protects patients and medical devices from excessive leakage currents that may flow through the data network. The network connection between an active medical device and an Ethernet network or a non-medical device, such as an office PC or laptop, is reliably galvanic separated according to the standard IEC EN 60601-1 (3rd edition) for medical devices and systems.

The MED MI 1005 network isolator can be used as an accessory or component of a medical-electrical device or system.This world - wide established network isolator offers a flexible and easy option for immediately isolating of medical equipment. In less than 5 seconds, patients, users and equipment are protected from dangerous leakage currents flowing via the data network. 

Under stress conditions the MI 1005 isolator was tested up to a  isolation stength of 10 kV DC (10 Sec.) and 5 kV AC (60 Sec.). Furthermore, 8 kV contact discharge and 16 kV air discharge are easily fulfiled. The Network Isolator MED MI 1005 is also available  as a build-in isolator or for wall mounting.

Benefits:

  • easy handling - no installation required
  • compact, sleek design and suitable for universal use
  • protects patients, users and equipment from dangerous leakage currents in less than 5 seconds
  • light and resistant housing - can be plugged into any system with a network connection
  • low-cost purchasing and efficient operation - no independent power supply required

 

Technical Data:
Isolation Voltage: 5,000 V
Data Speed: 10/100/1000 MBit/s
Conformity Ethernet: IEEE 802.3
Standards approved by: IEC 60601-1 (3rd Edition); IEC 60601-1-2 UL 60601 (UL Listed E342310)
Connections:: 2 x RJ45 input / output
Material: UL94V-0 / RoHS-compliant
Time between failures: 0.21 x 10 ^ 8 (1 error in 21 million hours)


For more information, please refer to our product information.

Scopes of Application for network isolators:

In medicine: Network isolators protect patients and medical devices from excessive leakage currents that may flow through the data network. Every device connected to the network represents a risk. This data network connection is ultimately also a risk for patients. The MI 1005 Ethernet Isolator protects patients, equipment and users from dangerous leakage currents that can appear unexpectedly at any time.
Measuring and monitoring: Network isolators protect sensitive measuring and monitoring devices in electrical testing laboratories, which are connected through an Ethernet network to a control centre, and need to be protected from transients and potential differences.
Server systems: In order to avoid failures or potential equalization currents, network isolators protect server systems which are connected over long distances via Ethernet cabling.
Audio applications: The MED MI 1005 reduce the transmission of low frequency alternating currents (AC hum) over the network connection.

Commissioning:

The Network Isolator MED MI 1005 can easaly be plugged into an existing network cabling by simply inserting. The passive electronic components do not require a separate power supply and behave completely transparently on the data network. Therefore, no installation of drivers or additional software is required.

Conformity and Certificates:

The MI 1005 network isolators fulfill the high requirements of current medical standards as per IEC 60601-1 (3rd Edition) and IEC 60601-1-2. For this reason, these galvanic network isolators are ideally suited to use in medical sectors. The MI 1005 network isolators are listed for their consistent quality by UL in accordance with applicable UL standards and requirements. Representative samples of this product have been assessed by UL and fulfill the applicable safety standards. Use on US and Canadian markets is therefore possible.

More about the product:

faq network isolators

Downloads:

Datasheet Network Isolator MED MI 1005 (Rev.10.3) 
Brochure Network Isolators  
MI_1005_Manual_V2.2.pdf

Related links to "Network Isolator MED MI 1005"
Read, write and discuss reviews... more
Customer evaluation for "Network Isolator MED MI 1005"
18 Oct 2019

Schnelle Lieferung und super Preis!

25 Jul 2018

Audioverbesserung durch Netzwerkisolator

Kaum zu glauben aber wahr. Ein Bekannter erzählte mir das er durch einen simplen Netzwerkisolator das Klangerlebnis beim streamen verbessert hat. Ist zwar nicht ganz billig, aber ich muss sagen es lohnt sich. Tatsache, das klingt anders! Und zwar besser. Der gesamte Hochtonbereich gewinnt an Auflösung. Klare Kaufempfehlung.

28 May 2018

Sehr robust

Das Gerät ist sehr robust und kompakt und die Installation ist sehr einfach (einstecken und los geht's). Die Übertragungsrate wird nicht merklich verlangsamt.
Kann den Kauf nur empfehlen

17 Apr 2018

Führt zu keiner Minderung der Übertragungsraten

Wir haben das Produkt gekauft, nachdem es trotz Einsatz eines Trenntransformators zu Störungen innerhalb unseres Systems gekommen ist. Nach einer kurzen Prüfung stellte sich raus, dass immer wenn wir das System eingeschaltet haben, enorme Spannungen innerhalb unseres Netzwerkes auftraten. Nach dem wir das Produkt einsetzten, sind keine weiteren Probleme mehr aufgetreten. Ein Verlust der Übertragungsraten ist auch nicht wahrzunehmen. Ein tolles Produkt, was ich nur empfehlen kann.

15 Feb 2018

Top

Super Preis - Leistungsverhältnis.
Haben das Produkt schon lange im Einsatz und sind mehr als zufrieden damit!

Write an evaluation
Evaluations will be activated after verification.

The fields marked with * are required.