Built in Medical Isolator MI 1005 E

Network Isolator MI 1005 MB Wall-mounted medical network isolator with Harting PushPull technology Safety: IEC 60601-1:2005/AMD1:2012/AMD2:2020 (Edition3.2) EMV: EN 60601-1-2:2015 (IEC 60601-1-2:2014) (Medical electrical equipment) The MI 1005 MB passive network isolator is specifically designed for wall mounting in medical environments. It provides galvanic network isolation for electronic medical devices and systems starting directly at the wall outlet. Once it is mounted to the wall, the isolator is well-protected by the housing. Accidental impacts can be absorbed, protecting the isolator and network cable connector from damage. The MI 1005 MB network isolator delivers dielectric strength up to 5 kV, up to 10 kV DC for 10 seconds under high-stress conditions. Coupled with Harting PushPull technology, an absolutely stable connection. No installation of drivers or additional software necessary because the MED MI 1005 MB network isolator behaves fully transparently on the data network. Benefits: Fixed installation – flush-mounted fitting Protects medical devices and patients against excessively high leakage currents in the data network Durable housing – absorbs minor impacts to protect the isolator and network connection cable No installation of drivers or additional software required Inexpensive and efficient operation. No dedicated power supply required Completely secure connection when coupled with Harting PushPull technology

Network Isolator MI 2005 2.5 GBit/s network isolator for secure galvanic isolation of the network interface Safety: IEC 60601-1:2005/AMD1:2012/AMD2:2020 (Edition 3.2) EMC: EN 60601-1-2:2015 (IEC 60601-1-2:2014) (medical electrical equipment) The new MI 2005 network isolator is now also designed for connecting current WLAN routers with transmission rates of up to 2.5 GBit/s. Key advantage: It can be operated with existing network cabling (Cat6). In accordance with the requirements of DIN EN 60601-1 (edition 3.2), it has two independent protective measures (2 MOPP) for patients and is therefore ideal for standard-compliant galvanic isolation of Ethernet-based signal interfaces within the patient environment. The new MI 2005 also has ESD and lightning protection properties. This protects connected devices and their users from surges caused by lightning, electrostatic discharges, etc. Areas of application The MI 2005 network isolator reliably protects patients, medical devices, and users from excessive leakage currents that flow through the data network and can occur unpredictably at any time. Measuring and monitoring equipment Sensitive measuring and monitoring devices in electrical test fields that are connected to a control center via Ethernet interfaces are protected against interference voltages and potential differences. Server systems To prevent failures or equipotential bonding currents, network isolators protect server systems that are connected over long distances using copper cabling. Audio applications The MI 2005 provides reliable protection against overvoltage, low-frequency AC voltage (mains hum) and prevents noise interference in the sound. Network isolators in medical technology In the medical field, the MI 2005 network isolator protects patients from leakage currents. The network connection between an active medical device and an Ethernet network or a non-medical device, such as an office PC, printer, or laptop, is safely galvanically isolated in accordance with the IEC 60601-1 standard for medical electrical equipment and systems. In accordance with the requirements of IEC 60601-1 (Edition 3.2), the MI 1005 network isolator has two independent protective measures (2 MOPP) for patients and is therefore ideal for standard-compliant galvanic isolation of Ethernet-based signal interfaces within the patient environment. Under stress conditions, the MI 2005 network isolator guarantees up to 10 kV DC (10 sec.) insulation strength and 5 kV AC (60 sec.), and also easily meets 8 kV contact discharge and 16 kV air discharge requirements. Example in patient environment DThe use of the MI 2055 ensures electrical safety in the patient environment in accordance with applicable standards – a simple, effective, and standards-compliant solution. Commissioning The MI 2005 network isolator can be put into operation by simply inserting it into existing network cabling. The passive electronic components do not require their own power supply and behave completely transparently in the data network. No drivers or additional software need to be installed. Benefits: Easy to use – no software installation required Compact and universally applicable In less than 5 seconds, the patient, user, and equipment are protected from dangerous leakage currents Lightweight and durable housing – can be connected to any system with a network connection Inexpensive to purchase and efficient to operate – does not require its own power supply Tested in accordance with IEC 60601-1:2005/AMD1:2012/AMD2:2020 Edition 3.2; and IEC 60601-1-2:2015 (4th edition)

Netzwerkisolator MI 1005 TÜV-certified network isolator for galvanic isolation Safety: IEC 60601-1:2005/AMD1:2012/AMD2:2020 (edition 3.2) EMV: EN 60601-1-2:2015 (IEC 60601-1-2:2014) (medical electric devices) The MI 1005 5 kV RJ-45 network isolator is used for the galvanic isolation of an Ethernet data line. It offers outstanding performance with only 1 dB attenuation and operates with virtually no loss in the data network over a distance of 100 m. Connected devices are reliably protected against external and internal overvoltages that can occur due to installation errors or environmental influences such as lightning strikes. The MI 1005 network isolator provides a flexible and simple way to immediately isolate medical devices. Users and inventory are protected in less than 5 seconds from dangerous leakage currents that can flow through the data network. Areas of application The MI 1005 network isolator reliably protects patients, medical devices, and users from excessive leakage currents flowing through the data network, which can occur unpredictably at any time. Measuring & monitoring devices Sensitive measuring and monitoring devices in electrical test fields that are connected to a control center via Ethernet interfaces are protected against interference voltages and potential differences. Server systems To prevent failures or equipotential bonding currents, network isolators protect server systems that are connected over long distances using copper cabling. Audio applications The MI 1005 provides reliable protection against power surges and low-frequency AC voltage (mains hum) and prevents noise interference in the sound. Network isolators in medical technology In the medical field, the MI 1005 network isolator serves to protect patients from leakage currents. The network connection between an active medical device and an Ethernet network or a non-medical device, such as an office PC, printer, or laptop, is safely galvanically isolated in accordance with the IEC 60601-1 standard for medical electrical equipment and systems. In accordance with the requirements of IEC 60601-1 (Edition 3.2), the MI 1005 network isolator has two independent protective measures (2 MOPP) for patients and is therefore ideal for the standard-compliant galvanic isolation of Ethernet-based signal interfaces within the patient environment. Under stress conditions, the MI 1005 network isolator guarantees up to 10 kV DC (10 sec.) insulation resistance and 5 kV AC (60 sec.), and also easily meets 8 kV contact discharge and 16 kV air discharge requirements. Example in a patient environment The use of the MI 1005 ensures electrical safety in the patient environment in accordance with applicable standards—a simple, effective, and standards-compliant solution. Commissioning The MI 2005 network isolator can be put into operation by simply inserting it into existing network cabling. The passive electronic components do not require their own power supply and behave completely transparently in the data network. No drivers or additional software need to be installed. Benefits: Easy to use – no software installation required Compact and universally applicable In less than 5 seconds, the patient, user, and equipment are protected from dangerous leakage currents Lightweight and durable housing – can be connected to any system with a network connection Inexpensive to purchase and efficient to operate – does not require its own power supply Tested in accordance with IEC 60601-1:2005/AMD1:2012/AMD2:2020 (Ausgabe 3.2)

Netzwerkisolator MI 1005 TÜV-certified network isolator for galvanic isolation Safety: IEC 60601-1:2005/AMD1:2012/AMD2:2020 (edition 3.2) EMV: EN 60601-1-2:2015 (IEC 60601-1-2:2014) (medical electric devices) The MI 1005 5 kV RJ-45 network isolator is used for the galvanic isolation of an Ethernet data line. It offers outstanding performance with only 1 dB attenuation and operates with virtually no loss in the data network over a distance of 100 m. Connected devices are reliably protected against external and internal overvoltages that can occur due to installation errors or environmental influences such as lightning strikes. The MI 1005 network isolator provides a flexible and simple way to immediately isolate medical devices. Users and inventory are protected in less than 5 seconds from dangerous leakage currents that can flow through the data network. Areas of application The MI 1005 network isolator reliably protects patients, medical devices, and users from excessive leakage currents flowing through the data network, which can occur unpredictably at any time. Measuring & monitoring devices Sensitive measuring and monitoring devices in electrical test fields that are connected to a control center via Ethernet interfaces are protected against interference voltages and potential differences. Server systems To prevent failures or equipotential bonding currents, network isolators protect server systems that are connected over long distances using copper cabling. Audio applications The MI 1005 provides reliable protection against power surges and low-frequency AC voltage (mains hum) and prevents noise interference in the sound. Network isolators in medical technology In the medical field, the MI 1005 network isolator serves to protect patients from leakage currents. The network connection between an active medical device and an Ethernet network or a non-medical device, such as an office PC, printer, or laptop, is safely galvanically isolated in accordance with the IEC 60601-1 standard for medical electrical equipment and systems. In accordance with the requirements of IEC 60601-1 (Edition 3.2), the MI 1005 network isolator has two independent protective measures (2 MOPP) for patients and is therefore ideal for the standard-compliant galvanic isolation of Ethernet-based signal interfaces within the patient environment. Under stress conditions, the MI 1005 network isolator guarantees up to 10 kV DC (10 sec.) insulation resistance and 5 kV AC (60 sec.), and also easily meets 8 kV contact discharge and 16 kV air discharge requirements. Example in a patient environment The use of the MI 1005 ensures electrical safety in the patient environment in accordance with applicable standards—a simple, effective, and standards-compliant solution. Commissioning The MI 2005 network isolator can be put into operation by simply inserting it into existing network cabling. The passive electronic components do not require their own power supply and behave completely transparently in the data network. No drivers or additional software need to be installed. Benefits: Easy to use – no software installation required Compact and universally applicable In less than 5 seconds, the patient, user, and equipment are protected from dangerous leakage currents Lightweight and durable housing – can be connected to any system with a network connection Inexpensive to purchase and efficient to operate – does not require its own power supply Tested in accordance with IEC 60601-1:2005/AMD1:2012/AMD2:2020 (Ausgabe 3.2)

Patch Cabel CAT6 PIMF, RoHS High-quality, halogen-free Ethernet cable for stable and fast network connections The patch cable CAT6 0.25m gray PIMF, RoHS is a high-quality Ethernet cable that was developed for transmitting data in Gigabit Ethernet networks. With a length of 0.25m, it is ideal for connecting network components in narrow installation areas. The cable has S/FTP (PiMF) shielding, in which each pair of wires is individually shielded with foil and the entire cable is also provided with a braided shield. This ensures a high level of interference immunity and reliable data transmission. The halogen-free jacket reduces the release of toxic gases in the event of a fire, thereby contributing to safety. The molded RJ45 connectors are equipped with gold-plated contacts and offer a stable connection. The molded kink protection sleeve protects the cable from mechanical stress and increases its service life. Benefits: Category-6 S/FTP patch cable Paired foil shielded with overall braid shield (PiMF) Halogen-free wrapping ISO/IEC 11801 Class E certified Shielded, molded RJ45 connector Colored, molded anti-kink grommet EIA/TIA B.2-1, EN 50173, RoHS compliant